home | alphabetical index | |||||

## Slide rule
The Once widely used for rapid, approximate scientific and engineering calculations, a slide rule is an analog computer consisting of three interlocking calibrated strips. The central strip can be moved lengthways relative to the other two. A sliding cursor with an alignment line can record an intermediate result on any of the scales.
One slide rule remains in daily use around the world, the ## Theory of operationDivision reverses this process. The illustration below shows the division of 22 by 2.75. The index (1) on the upper scale is aligned with the 2.75 on the lower scale. The 22 on the lower scale (the mark just to the left of the 22.5 mark) is aligned with the quotient, 8, on the upper scale.
Slide rules calibrated on one side were called "simplex." Slide rules calibrated on both sides were called "duplex." Typically two significant figures of precision were possible, with three being obtained by expert users who could estimate the fraction between gradations. Some high-end slide rules had magnifying cursors that basically doubled the accuracy, permitting a 10 inch slide rule to serve as well as a 20 inch. Slide rules often have other mathematical functions encoded on other auxiliary scales. The most popular were trigonometric, usually sine and tangent, logarithm of logarithm (base 10) (for taking the log of a value on a multiplier scale), natural logarithm and exponential scales. Some rules included a pythagorean scale, to figure sides of traiangles, and a scale to figure circles. Specialised slide rules were invented for various forms of engineering, business and banking. These often had common calculations directly expressed as special scales, for example loan calculations, optimal purchase quantities, or particular engineering equations. A number of tricks were used to get more convenience. Trigonometric scales were sometimes dual-labelled, in black and red, with complementary angles, the so-called "Darmstadt" style. Duplex slide rules often duplicated basic scales on the back. Scales were often "split" to get higher accuracy.
The basic advantage of a circular slide rule is that the longest dimension was reduced by a factor of about 3 (i.e. by &pi). For example, a 10cm circular would have a maximum accuracy equal to a 30cm ordinary slide rule. Circular slide rules were mechanically more rugged, smoother-moving and more precise than linear slide rules, because they depended on a single central bearing. The central pivot did not usually fall apart. The pivot also prevented scratching of the face and cursors. Only the most expensive linear slide rules had these features. The highest accuracy scales were placed on the outer rings. Rather than "split" scales, high-end circular rules used helical (snail-shell-shaped) scales for difficult things like log-of-log scales. One eight-inch premium circular rule had a 50 inch helical log-log scale! Circular slide rules also eliminate "off-scale" calculations, because the scales were designed to "wrap around." A real disadvantage of circular slide rules is that less-important scales are closer to the center, and have lower accuracies. The main disadvantage of circular slide rules was just that they were not standard. Most students learned on the linear slide rules, and never switched. ## MaterialsEarly cursors were metal frames holding glass. Later cursors were acrylics or polycarbonates sliding on teflon bearings. Magnifying cursors can both help engineers with bad eyes, and double the accuracy of a slide rule. Premium slide rules included clever catches so the rule would not fall apart by accident, and bumpers so that tossing the rule on the table would not scratch the scales or cursor. The recommended cleaning method for engraved markings is light scrubbing with steel-wool. For painted slide rules, and the faint of heart, use diluted commercial window-cleaning fluid and a soft cloth. ## HistorySlide rules came into wide use in the 1850s, as engineering became a recognized professional activity. In World War II, bombardiers, navigators, and other warriors who required quick calculations often used specialized slide rules. One office of the U.S. Navy actually designed a generic slide rule "chassis" with an aluminum body and plastic cursor into which celluloid cards (printed on both sides) could be placed for special calculations. The process was invented to calculate range, fuel-use and altitude for aircraft, and then adapted to many other purposes. Throughout the 1950s and 1960s the slide rule was the symbol of the engineer's profession in the same way that the stethoscope symbolized the medical profession. Some engineering students and engineers actually carried 5 inch pocket slide rules in their belts, in addition to using a 10 or 20 inch rule for precision work at home or at the office. All this came to an end in the 1970s, when the advent of miniaturised scientific calculators made slide rules obsolete.
Most slide rules are now collectors' items. A very popular model is the See also: Computing timeline, Abacus, Nomogram, Four Figure tables, Napier's bones, Counting rods ## External Links | |||||

copyright © 2004 FactsAbout.com |